Phil Ligrani
American academic
Phil Ligrani's AcademicInfluence.com Rankings
Download Badge
Engineering
Phil Ligrani's Degrees
- PhD Aerospace Engineering University of Notre Dame
- Masters Aerospace Engineering University of Notre Dame
- Bachelors Aerospace Engineering University of Notre Dame
Why Is Phil Ligrani Influential?
(Suggest an Edit or Addition)According to Wikipedia, Phillip Meredith Ligrani is a Professor of Mechanical and Aerospace Engineering at the University of Alabama in Huntsville. He is also the Eminent Scholar in Propulsion Research Center. Career Ligrani was born in Cheyenne, Wyoming. After receiving his Bachelor of Science degree in mechanical engineering from the University of Texas at Austin in 1974, he pursued his graduate studies at Stanford University where he received his master's degree in 1975 and his PhD in 1980. His doctoral dissertation was entitled The thermal and hydrodynamic behaviour of thick, roughwall, turbulent boundary layers. After completing his PhD he spent several years in Europe, first in a temporary faculty position at the Von Karman Institute for Fluid Dynamics in Belgium and then as a visiting senior research fellow at the Imperial College of Science and Technology in London. He returned to the United States in 1984, where he was an associate professor in the Department of Mechanical Engineering at the U.S. Naval Postgraduate School, a position he held until 1992. He joined the faculty of the Department of Mechanical Engineering at University of Utah in 1992 and became a full professor there in 1997.
Phil Ligrani's Published Works
Published Works
- Comparison of Heat Transfer Augmentation Techniques (2003) (367)
- Structure of transitionally rough and fully rough turbulent boundary layers (1986) (328)
- Spatial resolution and measurement of turbulence in the viscous sublayer using subminiature hot-wire probes (1987) (319)
- Heat transfer in a dimpled channel: combined influences of aspect ratio, temperature ratio, Reynolds number, and flow structure (2002) (274)
- Local Heat Transfer and Flow Structure on and Above a Dimpled Surface in a Channel (2000) (250)
- Flow structure due to dimple depressions on a channel surface (2001) (235)
- Effects Of Dimple Depth on Channel Nusselt Numbers and Friction Factors (2005) (178)
- Heat Transfer Augmentation Technologies for Internal Cooling of Turbine Components of Gas Turbine Engines (2013) (169)
- Flow structure and local Nusselt number variations in a channel with dimples and protrusions on opposite walls (2001) (162)
- Film-Cooling From Holes With Compound Angle Orientations: Part 1—Results Downstream of Two Staggered Rows of Holes With 3d Spanwise Spacing (1994) (153)
- Dean Flow Dynamics in Low-Aspect Ratio Spiral Microchannels (2017) (152)
- Film Cooling From Shaped Holes (2000) (151)
- Flow visualization of Dean vortices in a curved channel with 40 to 1 aspect ratio (1988) (136)
- Heat transfer in a channel with dimples and protrusions on opposite walls (2001) (121)
- Nusselt Number Behavior on Deep Dimpled Surfaces Within a Channel (2003) (116)
- Subminiature hot-wire sensors: development and use (1987) (113)
- Analysis and Experiments on Three-Dimensional, Irregular Surface Roughness (2002) (96)
- NUMERICAL PREDICTIONS OF FLOW STRUCTURE ABOVE A DIMPLED SURFACE IN A CHANNEL (2004) (94)
- Overtip Shock Wave Structure and Its Impact on Turbine Blade Tip Heat Transfer (2011) (83)
- NUMERICAL PREDICTIONS OF HEAT TRANSFER AND FLUID FLOW CHARACTERISTICS FOR SEVEN DIFFERENT DIMPLED SURFACES IN A CHANNEL (2005) (80)
- Numerical Simulation of Laminar Flow and Heat Transfer Inside a Microchannel With One Dimpled Surface (2007) (78)
- Comparisons of flow structure above dimpled surfaces with different dimple depths in a channel (2005) (73)
- Spatially-resolved heat transfer and flow structure in a rectangular channel with pin fins (2004) (72)
- Numerical analysis of flow structure and heat transfer characteristics in square channels with different internal-protruded dimple geometrics (2013) (71)
- Effects of Mach number and Reynolds number on jet array impingement heat transfer (2007) (69)
- Nusselt Numbers and Flow Structure on and Above a Shallow Dimpled Surface Within a Channel Including Effects of Inlet Turbulence Intensity Level (2005) (69)
- Transonic Turbine Blade Tip Aerothermal Performance With Different Tip Gaps—Part I: Tip Heat Transfer (2011) (67)
- Flow phenomena in swirl chambers (1997) (66)
- Heat Transfer and Flow Phenomena in a Swirl Chamber Simulating Turbine Blade Internal Cooling (1998) (66)
- Effects of hole spacing on spatially-resolved jet array impingement heat transfer (2008) (64)
- An infrared thermography imaging system for convective heat transfer measurements in complex flows (1998) (64)
- Local Swirl Chamber Heat Transfer and Flow Structure at Different Reynolds Numbers (1999) (63)
- NUMERICAL PREDICTIONS OF FLOW STRUCTURE AND LOCAL NUSSELT NUMBER RATIOS ALONG AND ABOVE DIMPLED SURFACES WITH DIFFERENT DIMPLE DEPTHS IN A CHANNEL (2004) (63)
- Miniature five-hole pressure probe for measurement of three mean velocity components in low-speed flows (1989) (63)
- Experimental and numerical investigation of unsteady impingement cooling within a blade leading edge passage (2014) (58)
- Effects of Dean vortex pairs on surface heat transfer in curved channel flow (1996) (56)
- Heat transfer, adiabatic effectiveness, and injectant distributions downstream of a single row and two staggered rows of compound angle film-cooling holes (1992) (55)
- Separate Effects of Mach Number and Reynolds Number on Jet Array Impingement Heat Transfer (2007) (52)
- Comparison of Heat Transfer Measurement Techniques on a Transonic Turbine Blade Tip (2011) (52)
- Flow structure and heat transfer in a square passage with offset mid-truncated ribs (2014) (50)
- Cross-flow effects on impingement array heat transfer with varying jet-to-target plate distance and hole spacing (2014) (49)
- Crossflows from jet array impingement cooling: Hole spacing, target plate distance, Reynolds number effects (2015) (47)
- Aero-Thermal Performance of a Winglet at Engine Representative Mach and Reynolds Numbers (2010) (46)
- Spatial resolution and downwash velocity corrections for multiple-hole pressure probes in complex flows (1989) (42)
- Spatially Resolved Surface Heat Transfer for Parallel Rib Turbulators With 45 Deg Orientations Including Test Surface Conduction Analysis (2004) (40)
- Bulk flow pulsations and film cooling—I. Injectant behavior (1996) (39)
- Transonic Aerodynamic Losses Due to Turbine Airfoil, Suction Surface Film Cooling (1999) (38)
- Heat transfer in a swirl chamber at different temperature ratios and Reynolds numbers (1999) (38)
- Comparisons of flow structure and local Nusselt numbers in channels with parallel- and crossed-rib turbulators (2004) (38)
- Thermal performance of dimpled surfaces in laminar flows (2009) (35)
- Single-disk and double-disk viscous micropumps (2005) (35)
- Features of wavy vortices in a curved channel from experimental and numerical studies (1992) (35)
- The thermal and hydrodynamic behavior of thick, rough-wall, turbulent boundary layers (1979) (34)
- Transonic Film Cooling Effectiveness from Shaped Holes on a Simulated Turbine Airfoil (2002) (34)
- Milliscale confined impinging slot jets: Laminar heat transfer characteristics for an isothermal flat plate (2012) (33)
- Film Cooling From Spanwise-Oriented Holes in Two Staggered Rows (1995) (33)
- Bulk flow pulsations and film cooling—II. Flow structure and film effectiveness (1996) (33)
- Full-Coverage Film Cooling: Film Effectiveness and Heat Transfer Coefficients for Dense and Sparse Hole Arrays at Different Blowing Ratios (2012) (32)
- Miniature Single-Disk Viscous Pump "Single-DVP…, Performance (2006) (32)
- Assessment of six turbulence models for modeling and predicting narrow passage flows, part 2: Pin fin arrays (2016) (32)
- Confined, milliscale unsteady laminar impinging slot jets and surface Nusselt numbers (2011) (32)
- Spatially Resolved Heat Transfer and Friction Factors in a Rectangular Channel With 45-Deg Angled Crossed-Rib Turbulators (2003) (30)
- Numerical Predictions of Heat Transfer and Flow Characteristics of Heat Sinks with Ribbed and Dimpled Surfaces in Laminar Flow (2008) (30)
- A Reynolds analogy for real component surface roughness (2002) (30)
- Effects of Embedded Vortices on Film-Cooled Turbulent Boundary Layers (1988) (30)
- Effects of Jet-to-Target Plate Distance and Reynolds Number on Jet Array Impingement Heat Transfer (2013) (29)
- Shock Wave–Film Cooling Interactions in Transonic Flows (2001) (28)
- Endwall aerodynamic losses from turbine components within gas turbine engines (2017) (28)
- Effects of surface roughness and freestream turbulence on the wake turbulence structure of a symmetric airfoil (2004) (28)
- Effect of Temperature Ratio on Jet Array Impingement Heat Transfer (2007) (28)
- Slip and accommodation coefficients from rarefaction and roughness in rotating microscale disk flows (2007) (27)
- Effects of Surface Roughness and Turbulence Intensity on the Aerodynamic Losses Produced by the Suction Surface of a Simulated Turbine Airfoil (2004) (27)
- Effects of Double Wall Cooling Configuration and Conditions on Performance of Full-Coverage Effusion Cooling (2017) (27)
- Jet Impingement Cooling of Chips Equipped With Multiple Cylindrical Pedestal Fins (2007) (26)
- Influence of Surface Roughness on the Aerodynamic Losses of a Turbine Vane (2006) (26)
- Numerical Predictions of Heat Transfer and Flow Structure in a Square Cross-Section Channel with Various Non-Spherical Indentation Dimples (2013) (26)
- Film Cooling from a Single Row of Compound Angle Holes at High Blowing Ratios (1996) (25)
- Aerodynamic Losses of a Cambered Turbine Vane: Influences of Surface Roughness and Freestream Turbulence Intensity (2006) (25)
- Effects of Vortices With Different Circulations on Heat Transfer and Injectant Downstream of a Single Film-Cooling Hole in a Turbulent Boundary Layer (1990) (25)
- Flow in a simple swirl chamber with and without controlled inlet forcing (1999) (25)
- Film cooling subject to bulk flow pulsations: effects of blowing ratio, freestream velocity, and pulsation frequency (1999) (23)
- Mach Number, Reynolds Number, Jet Spacing Variations: Full Array of Impinging Jets (2010) (23)
- Effects of an Embedded Vortex on Injectant From a Single Film-Cooling Hole in a Turbulent Boundary Layer (1989) (23)
- The effect of injection hole length on film cooling with bulk flow pulsations (1998) (23)
- Temperature and Heat Flux (2007) (23)
- Flow structure and local Nusselt number variations in a channel with angled crossed-rib turbulators (2003) (22)
- Artificially Thickened Turbulent Boundary Layers for Studying Heat Transfer and Skin Friction on Rough Surfaces (1983) (22)
- Variable Property and Temperature Ratio Effects on Nusselt Numbers in a Rectangular Channel With 45 Deg Angled Rib Turbulators (2003) (22)
- Effects of Dimple Depth on Nusselt Numbers and Friction Factors for Internal Cooling in a Channel (2004) (22)
- Impingement jet array heat transfer with small-scale cylinder target surface roughness arrays (2017) (22)
- Effect of Reynolds Number, Hole Patterns, and Hole Inclination on Cooling Performance of an Impinging Jet Array—Part I: Convective Heat Transfer Results and Optimization (2017) (22)
- Variable Property Nusselt Numbers in a Channel with Pin Fins (2003) (21)
- Splitting, merging and spanwise wavenumber selection of Dean vortex pairs (1994) (20)
- Transonic Turbine Blade Tip Aero-Thermal Performance With Different Tip Gaps: Part II—Tip Aerodynamic Loss (2010) (19)
- Transition to turbulent flow in curved and straight channels with heat transfer at high Dean numbers (1998) (19)
- Aerodynamic Performance of Suction-Side Gill Region Film Cooling (2010) (19)
- Double Wall Cooling of a Full-Coverage Effusion Plate, Including Internal Impingement Array Cooling (2018) (19)
- Recent investigations of shock wave effects and interactions (2020) (19)
- Full-Coverage Film Cooling: Film Effectiveness and Heat Transfer Coefficients for Dense Hole Arrays at Different Hole Angles, Contraction Ratios, and Blowing Ratios (2012) (19)
- Interactions Between Embedded Vortices and Injectant From Film Cooling Holes With Compound Angle Orientations in a Turbulent Boundary Layer (1992) (19)
- Effects of Bulk Flow Pulsations on Film Cooling With Compound Angle Holes: Heat Transfer Coefficient Ratio and Heat Flux Ratio (2001) (18)
- Numerical Analysis of Flow Structure and Heat Transfer Characteristics in Dimpled Channels With Secondary Protrusions (2016) (18)
- Adiabatic Film Cooling Effectiveness From Heat Transfer Measurements in Compressible, Variable-Property Flow (1985) (18)
- Suction-Side Gill Region Film Cooling: Effects of Hole Shape and Orientation on Adiabatic Effectiveness and Heat Transfer Coefficient (2010) (18)
- A Study of Dean Vortex Development and Structure in a Curved Rectangular Channel with Aspect Ratio of 40 at Dean Numbers up to 430 (1994) (18)
- Slip due to surface roughness for a Newtonian liquid in a viscous microscale disk pump (2010) (18)
- A wind tunnel for the calibration of Mars wind sensors (2008) (18)
- Effects of Exterior Surface Dimples on Heat Transfer and Friction Factors for a Cross-Flow Heat Exchanger (2006) (18)
- Influences of target surface small-scale rectangle roughness on impingement jet array heat transfer (2017) (18)
- Measurements in the vaneless diffuser of a radial flow compressor (1983) (17)
- Flow characteristics along and above dimpled surfaces with three different dimple depths within a channel (2007) (17)
- Experimental Surface Heat Transfer and Flow Structure in a Curved Channel With Laminar, Transitional, and Turbulent Flows (2004) (17)
- Numerical predictions of detailed flow structural characteristics in a channel with angled rib turbulators (2015) (17)
- Unsteady Structure and Development of a Row of Impingement Jets, Including Kelvin–Helmholtz Vortex Development (2015) (17)
- Fabrication and testing of subminiature multi-sensor hot-wire probes (1989) (17)
- Jet Impingement Cooling of Chips Equipped With Cylindrical Pedestal Profile Fins (2005) (17)
- Effects of Bulk Flow Pulsations on Film Cooling From Different Length Injection Holes at Different Blowing Ratios (1998) (16)
- Effects of hole shape on impingement jet array heat transfer with small-scale, target surface triangle roughness (2018) (16)
- Mixed convection in straight and curved channels with buoyancy orthogonal to the forced flow (1996) (16)
- Determination of rough-surface skin friction coefficients from wake profile measurements (2003) (16)
- Effects of Bulk Flow Pulsations on Film-Cooled Boundary Layer Structure (1997) (16)
- Bulk Flow Pulsations and Film Cooling: Flow Structure Just Downstream of the Holes (1995) (16)
- Mach number and freestream turbulence effects on turbine vane aerodynamic losses (2005) (15)
- Transonic Turbine Blade Tip Aero-Thermal Performance With Different Tip Gaps: Part I—Tip Heat Transfer (2010) (15)
- Unsteady heat transfer and flow structure of a row of laminar impingement jets, including vortex development (2015) (15)
- Flow visualization and flow tracking as applied to turbine components in gas turbine engines (2000) (14)
- Aerodynamic Losses in Turbines with and without Film Cooling, as Influenced by Mainstream Turbulence, Surface Roughness, Airfoil Shape, and Mach Number (2012) (14)
- Comparisons of different viscous pumps based on physical flow behavior (2006) (14)
- Impingement Jet Array Heat Transfer: Target Surface Roughness Shape, Reynolds Number Effects (2017) (14)
- Heat Transfer Enhancements from Elastic Turbulence Using Sucrose-Based Polymer Solutions (2018) (13)
- Investigations of Performance Characteristics Including Limitations Due to Flow Instabilities in Continuous SPLITT Fractionation (1997) (13)
- Spatially-Resolved Heat Transfer and Flow Structure in a Rectangular Channel With 45° Angled Rib Turbulators (2002) (13)
- Assessment of six turbulence models for modeling and predicting narrow passage flows, part 1: Impingement jets (2016) (13)
- Film cooling subject to bulk flow pulsations: effects of density ratio, hole length-to-diameter ratio, and pulsation frequency (2001) (13)
- Film cooling effectiveness distribution on first-stage vane endwall with and without leading-edge fillets (2013) (13)
- Mach Number/Surface Roughness Effects on Symmetric Transonic Turbine Airfoil Aerodynamic Losses (2004) (12)
- Effects of Double Wall Cooling Configuration and Conditions on Performance of Full Coverage Effusion Cooling (2016) (12)
- Double Wall Cooling of a Full-Coverage Effusion Plate With Main Flow Pressure Gradient, Including Internal Impingement Array Cooling (2019) (12)
- Full-Coverage Film Cooling: Heat Transfer Coefficients and Film Effectiveness for a Sparse Hole Array at Different Blowing Ratios and Contraction Ratios (2013) (12)
- Thermal boundary layers on a rough surface downstream of steps in wall temperature (1985) (11)
- Thin film heat transfer gage construction and measurement details (1982) (11)
- Effects of Embedded Vortices on Injectant From Film Cooling Holes With Large Spanwise Spacing and Compound Angle Orientations in a Turbulent Boundary Layer (1993) (10)
- Effect of Reynolds Number, Hole Patterns and Hole Inclination on Cooling Performance of an Impinging Jet Array: Part I — Convective Heat Transfer Results and Optimization (2016) (10)
- Internal and external cooling of a full coverage effusion cooling plate: Effects of double wall configuration and conditions (2018) (10)
- Flow and heat transfer characteristics of micro pin-fins under jet impingement arrays (2019) (10)
- Wake Turbulence Structure Downstream of a Cambered Airfoil in Transonic Flow: Effects of Surface Roughness and Freestream Turbulence Intensity (2006) (10)
- Performance and Development of a Miniature Rotary Shaft Pump (2005) (10)
- Effect of Hole Spacing on Jet Array Impingement Heat Transfer (2007) (9)
- Second Law Analysis of Aerodynamic Losses: Results for a Cambered Vane With and Without Film Cooling (2012) (9)
- Artificially Thickening a Smooth-Wall Turbulent Boundary Layer (1979) (9)
- Flow and heat transfer in swirl tubes — A review (2022) (9)
- Numerical Predictions of Stanton Numbers, Skin Friction Coefficients, Aerodynamic Losses, and Reynolds Analogy Behavior for a Transsonic Turbine Vane (2006) (9)
- Surface heat transfer and flow properties of vortex arrays induced artificially and from centrifugal instabilities (1992) (9)
- A heat transfer prediction method for turbulent boundary layers developing over rough surfaces with transpiration (1979) (9)
- Film Cooling from Two Staggered Rows of Compound Angle Holes at High Blowing Ratios (1996) (9)
- EVOLUTION OF SECONDARY DEAN VORTICES IN SPIRAL MICROCHANNELS FOR CELL SEPARATIONS (2013) (9)
- Double Wall Cooling of a Full Coverage Effusion Plate With Cross Flow Supply Cooling and Main Flow Pressure Gradient (2018) (9)
- Flow structure and surface heat transfer from a turbine component endwall contoured using the ice formation method (2018) (9)
- Internal and External Cooling of a Full Coverage Effusion Cooling Plate: Effects of Double Wall Cooling Configuration and Conditions (2017) (9)
- Heat transfer in film-cooled turbulent boundary layers at different blowing ratios as affected by longitudinal vortices (1988) (8)
- Heat transfer in curved and straight channels with transitional flow (1998) (8)
- Elastic turbulence influences and convective heat transfer within a miniature viscous disk pump (2017) (8)
- Visualization and structure of confined, milliscale, unsteady impinging slot jets and associated vortices (2012) (8)
- Film Cooling From a Single Row of Holes Oriented in Spanwise/Normal Planes (1997) (7)
- Double wall cooling of an effusion plate with cross flow and impingement jet combination internal cooling: Comparisons of main flow contraction ratio effects (2019) (7)
- WINGLET-PAIR TARGET SURFACE ROUGHNESS INFLUENCES ON IMPINGEMENT JET ARRAY HEAT TRANSFER (2019) (7)
- Linear Cascade and Wind Tunnel Development for Turbine Blade Tip Heat Transfer Investigations With and Without Film Cooling (2019) (7)
- A sensor for flow measurements near the surface of a compressor blade (1983) (7)
- Analysis of shock wave unsteadiness using space and time correlations applied to shadowgraph flow visualization data (2019) (7)
- Experimental validation of an inverse heat conduction problem using thermocouple and infrared data (2001) (7)
- Onset and effects of instabilities from unstable stratification of density on mass transfer in channel shear layers at low Reynolds numbers (1998) (7)
- Study of the imposition of bulk flow pulsations on plane channel flow at moderate stokes numbers (1992) (6)
- Effects of coolant supply arrangement on double wall cooling: Hot-side effusion performance and cold-side Nusselt numbers at different initial blowing ratios (2020) (6)
- Thermal Transport of Viscoelastic Fluids Within Rotating Couette Flows (2020) (6)
- Performance and Development of a Miniature Rotary Shaft Pump (RSP) (2004) (6)
- Numerical Analysis of Flow Structure Above Dimpled Surfaces with Different Depths in a Channel (2015) (6)
- Crossflows From Jet Array Impingement Cooling: Effects of Hole Array Spacing, Jet-to-Target Plate Distance, and Reynolds Number (2014) (6)
- Vortex generation in a finitely extensible nonlinear elastic Peterlin fluid initially at rest (2020) (6)
- Rotating Stall Measurements in the Vaneless Diffuser of a Radial Flow Compressor (1982) (6)
- Double Wall Cooling of an Effusion Plate With Simultaneous Cross Flow and Impingement Jet Array Internal Cooling (2019) (6)
- Resolution deterioration and optimal operating conditions in centrifugal SPLITT fractionation. Part I: Stable density gradients (1997) (6)
- Numerical second law analysis around a turbine guide vane using a two-equation turbulence model and comparison with experiments (2017) (5)
- Effects of Bulk Flow Pulsations on Phase-Averaged and Time-Averaged Film-Cooled Boundary Layer Flow Structure (2001) (5)
- Shock Wave - Film Cooling Interactions in Transonic Flows (2001) (5)
- Effects of gap size for parallel 45 degree angled rib turbulators (2016) (5)
- Influences of Target Surface Roughness on Impingement Jet Array Heat Transfer: Part 2 — Effects of Roughness Shape, and Reynolds Number (2016) (5)
- Confined, Milliscale Unsteady Laminar Impinging Slot Jets: Effects of Slot Width on Surface Stagnation Point Nusselt Numbers (2012) (5)
- Numerical investigation of adiabatic film cooling effectiveness through compound angle variations (2020) (5)
- Subminiature Hot-Wire Sensor Construction (1984) (5)
- Spiral inertial microfluidic devices for continuous blood cell separation (2012) (5)
- Control of embedded longitudinal vortices using a wall jet (1990) (5)
- Parametric study of wind tunnel test section configurations for stabilizing normal shock wave structure (2020) (5)
- Development and structure of a film-cooling jet in a turbulent boundary layer with heat transfer (1992) (5)
- Double Wall Cooling of a Full Coverage Effusion Plate, Including Internal Impingement Array Cooling (2017) (5)
- Micro-structure mechanical failure characterization using rotating Couette flow in a small gap (2005) (5)
- Effects of coolant and wall temperature variations on impingement jet array thermal performance (2021) (4)
- Louver and effusion cooling heat transfer for a double wall effusion plate with impingement jet array coolant supply (2021) (4)
- Deviations Due to Non-Newtonian Influences Within a Miniature Viscous Disk Pump (2013) (4)
- Optimization of an Innovative Rotary Shaft Pump (RSP) (2006) (4)
- Development of subminiature multi-sensor hot-wire probes (1988) (4)
- MINIATURE VISCOUS DISK PUMP: PERFORMANCE VARIATIONS FROM NON-NEWTONIAN ELASTIC TURBULENCE (2017) (4)
- Flow and heat transfer characteristics in a pre-swirl rotor-stator cavity (2022) (4)
- Osmotic dispense pump for operation at different temperatures and pressures (2007) (4)
- Influences of Target Surface Roughness on Impingement Jet Array Heat Transfer: Part 1 — Effects of Roughness Pattern, Roughness Height, and Reynolds Number (2016) (4)
- Louver Slot Cooling and Full-Coverage Film Cooling With a Combination Internal Coolant Supply (2020) (3)
- DEVELOPMENT AND CONTROL OF ELASTIC TURBULENCE WITHIN A MICRO-SCALE VISCOUS DISC PUMP (2016) (3)
- JET ARRAY IMPINGEMENT COOLING LOCAL NUSSELT NUMBER VARIATIONS: EFFECTS OF HOLE ARRAY SPACING, JET-TO-TARGET PLATE DISTANCE, AND REYNOLDS NUMBER (2016) (3)
- Secondary flows and extra heat transfer enhancement of ribbed surfaces with jet impingement (2017) (3)
- Flow structure and surface heat transfer from numerical predictions for a double wall effusion plate with impingement jet array cooling (2022) (3)
- Vortex Structure Effects on Impingement, Effusion, and Cross Flow Cooling of a Double Wall Configuration (2018) (3)
- Characteristics of flow instabilities from unstable stratification of density in channel shear layers at low Reynolds numbers (1999) (3)
- Effects of Surface Roughness and Turbulence Intensity on the Aerodynamics Losses Produced by a Suction Surface of a Simulated Turbine Airfoil (2003) (3)
- Elastic Turbulence Effects on the Performance of a Miniature Viscous Disk Pump (2015) (2)
- Suction-Side Gill-Region Film Cooling: Effects of Hole Shape and Orientation on Adiabatic Effectiveness and Heat Transfer Coefficient (2008) (2)
- Spatial coherence of low-frequency unsteadiness associated with a normal shock wave (2021) (2)
- Recent research developments for turbine blade tip heat transfer, including development and effects of tip leakage vortices (2020) (2)
- Buoyancy-Driven Continuous SPLITT Fractionation: A New Technique for Separation of Microspheres (2009) (2)
- Dimple Array Effects on Turbulent Heat Transfer and Flow Structure (2006) (2)
- Modeling the Socio-Economic Impacts of Covid-19 Using an Improved Traditional Travel Demand Model (2020) (2)
- Propulsion Research and Academic Programs at the University of Alabama in Huntsville - 30th Anniversary Summary (2017) (2)
- Rotating Stall in an Axial Flow Single Stage Compressor. On-Blade Velocity Measurements. (1982) (2)
- Instabilities of Nonreturn Valves in Low-Speed Air Systems (2008) (2)
- Single-Disk and Double-Disk Viscous Micropump (2004) (2)
- Micro-scale and millimeter-scale rotating disk couette flows, experiments and analysis (2006) (2)
- Effects of different crash data variables on EMS response time for a rural county in alabama (2022) (2)
- Cylindrical Multiple Target Surface Roughness Effects On Impingement Jet Array Surface Heat Transfer (2017) (1)
- Numerical Simulation of Flow and Heat Transfer Inside a Micro-Channel With One Dimpled Surface (2002) (1)
- Influences of Target Surface Cylindrical Roughness on Impingement Jet Array Heat Transfer: Effects of Roughness Height, Roughness Shape, and Reynolds Number (2016) (1)
- Full-Coverage Effusion Cooling in External Forced Convection: Sparse and Dense Hole Arrays (2017) (1)
- EMS Response Time for Patients Critically-Injured from Automobile Accidents Using Regression Analysis (2021) (1)
- Effects of pressure side film cooling hole placement and condition on adiabatic film cooling effectiveness characteristics of a transonic turbine blade tip (2022) (1)
- Particulate Deposition Effects On Internal Swirl Cooling of Turbine Blades (2022) (1)
- Resolution deterioration and optimal conditions in centrifugal SPLITT Fractionation. Part I: Stable density gradients and Part II: Unstable density gradients (1997) (1)
- Experimental study of turbulent flow heat transfer and pressure loss over surfaces with dense micro-depth dimples under viscous sublayer (2022) (1)
- Development of customized shear layers on smooth and rough surfaces (1986) (1)
- IMPINGEMENT ARRAY HEAT TRANSFER WITH LARGE HOLE SPACING (2016) (1)
- Investigations of the Effects of Bulk Flow Pulsations on Film Cooling as Applied to Gas Turbine Engines (1998) (1)
- Recent Developments in Impingement Array Cooling, Including Consideration of the Separate Effects of Mach Number, Reynolds Number, Temperature Ratio, Hole Spacing, and Jet-to-Target-Plate Distance (2014) (1)
- Heat Transfer Measurements from Concave and Convex Surfaces with a Fully Developed Confined Impinging Slot Jet (2014) (1)
- Effects of Coolant Supply Arrangement on Hot-Side Effusion Performance and Cold-Side Nusselt Numbers at Different Initial Blowing Ratios (2019) (1)
- Double Wall Cooling of a Full Coverage Effusion Plate With Main Flow Pressure Gradient, Including Internal Impingement Array Cooling (2018) (1)
- Correction: Propulsion Research and Academic Programs at the University of Alabama in Huntsville - PRC Graduate Student Production History (2020) (1)
- Unsteady Structure and Development of a Row of Impingement Jets, Including Shear Layer and Vortex Development: Part 2 — Laminar Jets (2015) (0)
- Surface film cooling characteristics of rectangular holes along the trailing edge of a transonic turbine blade tip (0)
- Analysis of shock wave unsteadiness using space and time correlations applied to shadowgraph flow visualization data (2019) (0)
- Reply to “comments on ‘a heat transfer prediction method for turbulent boundary layers developing over rough surfaces with transpiration’” (1984) (0)
- DOWNSTREAM OF STEPS IN WALL TEMPERATURE (1985) (0)
- Subminiature Hot-Wire Probes (1989) (0)
- Transient, Oscillatory and Steady Characteristics of Dean Vortex Pairs in a Curved Rectangular Channel (1992) (0)
- Transonic Turbine Blade Tip Heat Transfer with Pressure Side Film Cooling (2022) (0)
- Second Law Analysis of Aerodynamic Gains Associated with Simple Angle and Compound Angle Full Coverage Film Cooling (2021) (0)
- Front Cover Image, Volume 2, Number 3, March 2020 (2020) (0)
- Recent investigations of shock wave effects and interactions (2020) (0)
- Visualization and structure of confined, milliscale, unsteady impinging slot jets and associated vortices (2012) (0)
- Characterization of Effective Diffusion within Viscoelastic Fluids with Elastic Instabilities (2022) (0)
- Discussion: “Heat Transfer in Rotating Rectangular Cooling Channels (AR=4) With Dimples” (T. S. Griffith, L. Al. Hadhrami, and J.-C. Han., 2003, ASME J. Turbomach. 125, pp. 555–563) (2003) (0)
- Special Issue on Gas Turbine Heat Transfer: Part 2 (2005) (0)
- Effects of Dusting Film Cooling Placement and Configuration on Surface Heat Transfer Characteristics of a Transonic Turbine Squealer Blade Tip (2023) (0)
- Clarification: Heat Transfer Enhancements from Elastic Turbulence Using Sucrose-Based Polymer Solutions (2017) (0)
- Dusting Hole Film Cooling Heat Transfer on a Transonic Turbine Blade Tip (2022) (0)
- Turbullent shear flows : February 28 - March 4, 1983 (1983) (0)
- Numerical predictions of detailed flow structural characteristics in a channel with angled rib turbulators (2015) (0)
- Measurement and determination of local film cooling performance along a transonic turbine blade tip with viscous dissipation (2022) (0)
- Discussion: “Behavior of a Coolant Film With Two Rows of Holes Along the Pressure Side of a High-Pressure Nozzle Guide Vane” (Arts, T., and Bourguignon, A. E., 1990, ASME J. Turbomach., 112, pp. 512–520) (1990) (0)
- Louver Slot Cooling and Full Coverage Film Cooling with Combination Coolant (2022) (0)
- Viscous Disk Air Flow Displacement Device (VDAFDD): Development and Performance (2010) (0)
- Comparisons of Cooling Performance and Flow Characteristics of a Combustor Liner Plate with Compound Angle and Simple Angle Effusion Holes (2023) (0)
- Second law analysis of aerodynamic characteristics with flow temperature variations of simple angle and compound angle full coverage film cooling (2022) (0)
- Impingement array cooling recent developments: Effects of mach number, reynolds number, temperature ratio, hole spacing, and jet-to-target-plate distance (2014) (0)
- Microscale disk-induced gas displacement with and without slip (2007) (0)
- Parametric study of wind tunnel test section configurations for stabilizing normal shock wave structure (2019) (0)
- Slip due to Rarefaction, Surface Roughness, and Intermolecular Interactions for Gases and Liquids (2011) (0)
- Investigation of Shock Wave - Boundary Layer Interactions in a 3.57 Aspect Ratio Wind Tunnel (2014) (0)
- Celebration of Professor Bernhard Weigand on his 60th birthday (2022) (0)
- Improved understanding of combustor liner cooling (2009) (0)
This paper list is powered by the following services:
Other Resources About Phil Ligrani
What Schools Are Affiliated With Phil Ligrani?
Phil Ligrani is affiliated with the following schools: